Component and circuit board identifier
From circuit board to pinout, with your camera
Take one photo of a circuit board and Rainbohm puts a box around the parts. Point the camera at a single part and it reads the markings, the SMD code or the colour bands, and tells you what it is, how to measure it and what to watch for when you replace it. With all the codes and calculators, a dossier for every repair and a database that works offline.
What Rainbohm does
Identify, look up, measure and keep track
From a whole circuit board to a single loose part: Rainbohm recognises it, tells you what it is and helps you measure and replace it. All on your phone, even without internet.
A circuit board in one photo New
One photo, and every part we find gets a box. Tap a box to see what it is.
Loose parts and markings
Capacitor, diode, transistor, chip, crystal, fuse or relay: it recognises what it is and reads the codes and type numbers on it.
Resistors Free
Colour bands read without white paper, with candidates when it is not sure. Also a handful at once.
Component database
What it is, what it does, the pinout, how to measure it and what to watch for when you replace it. Works offline.
Codes and calculators Free
SMD and capacitor codes, fuses, Ohm's law, a substitute built from standard values and much more.
Repair dossiers
For each device the photo, your notes and the status of every part. With a shopping list and your parts bin.
Circuit board
A whole circuit board in one photo
Take one photo of a circuit board, straight from above and in good light, and Rainbohm puts a box around every part it finds. You see at a glance what is on it, and then tap the parts you want to know about.
- Tap a box: if the part carries a code or type number, you see what it is, and if a resistor has colour bands, you get the value. The box gets a label, such as 470 µF.
- Zoom in with two fingers, down to the small parts.
- No markings, or too small? Many small parts have no markings or are too small in a photo of the whole board. Read those up close with Part.
- Three free scans to try it; unlimited with the full version.
Markings and loose parts
Reads what is printed on a part
Rainbohm recognises the type of a loose part, from resistor, capacitor and diode to transistor, chip, crystal, fuse and relay. With text recognition on the phone itself, it reads the codes and type numbers printed on it, and tells you in two short lines what the part is and what it does.
- SMD codes on resistors and capacitors, such as 103, 4R7 and 01C.
- Electrolytic capacitors with capacitance, voltage and temperature, ceramic capacitor codes, fuses, crystals and relays.
- Type numbers of chips and transistors, in the full version.
- Characters that look alike, such as 0 and O or 8 and B, give extra candidates instead of a wrong answer. The package, such as SOT-23 or TO-92, narrows down what an SMD code means.
Short first
Electrolytic capacitor 470 µF, 25 V
Smooths the voltage in a power supply. Bulging or leaking: a known cause of a power supply that no longer starts.
Every answer starts with two lines like these. Tap to see the rest.
Component database
What it is, what it does, how to measure it
Rainbohm comes with its own database of the components you meet when repairing, stored on your phone and usable without a connection: regulators, transistors, MOSFETs, op-amps, timers, optocouplers, rectifiers, microcontrollers and audio chips. We check every entry by hand against the manufacturer's datasheet and write it in our own words.
What it is and what it does
Two short lines first, with a typical fault where there is one. The rest opens when you tap.
Pinout and package
A clear drawing with the pin names, the package and the most important limits.
How to measure
Which multimeter setting to use, and what a good and a faulty part measures.
What to watch when replacing
The values that must match, the polarity, and replacements, with a warning when the pins are in a different order.
Safety first
Unplug a device before you open it. Large electrolytic capacitors can stay charged for a long time, even with the plug out. Never measure on parts that carry mains voltage.
Help with measuring, not with mains
Rainbohm explains how to measure a part and what to watch when you replace it, always with this safety note. We do not give step-by-step repairs of parts that carry mains voltage.
Colour bands
Resistors, without white paper
Most colour code scanners want the resistor flat on a sheet of white paper, and still give a different value with every photo. Rainbohm reads it in your hand or on the circuit board, and only answers when several frames from the viewfinder agree.
3 to 6 bands
Beige and blue bodies, with white, grey, gold and silver bands. Rainbohm works out the reading direction itself.
Candidates when unsure
Two to four candidates, each drawn as a resistor with its value and likelihood, and the doubtful band marked on your own photo. One tap picks the right one.
A handful at once
Lay loose parts on a plain surface and take one photo. Rainbohm reads the bands of every resistor; tap the others to read their markings.
Colour names in text
Every band is also written out by name, and the app can read the answer aloud. Helpful if colours are hard to tell apart.
Correct in one tap
Change a band or flip the reading direction. Standard values from the E-series count as more likely.
Adjusts to your light
Keep choosing red where the app read orange under your lamp, and it adjusts the colours for your phone. On your phone only.
Codes and calculators
All the codes you need for repairs, free
The calculators work both ways, offline, and stay free. Type values the way you write them, such as 4k7 or R47.
Resistor colour code
3 to 6 bands, colours to value and value to colours, and check a measurement against the tolerance.
SMD resistor codes
3 and 4 digits, R notation and EIA-96. When a code can be read two ways, you see both.
Capacitor codes
Codes such as 104, 4n7 and 473K, letters for tolerance and voltage, tantalum and electrolytic markings.
Inductors
Colour bands and printed codes.
Fuses
Markings such as T2A L250V: current, voltage, fast or slow.
Diodes, zeners and LEDs
Which leg is which, the cathode ring, and the typical voltage per LED colour.
E-series
Is this a standard value, and which one is closest?
LED series resistor
The right resistor for an LED, from the supply voltage and the current.
Ohm's law and power
Voltage, current, resistance and power from any two.
Series and parallel
Combine resistors and capacitors.
Replacement composer
No 4.7 kΩ at hand? Take 2.2 kΩ and 2.7 kΩ in series: 4.9 kΩ. Made from standard values.
Units and practice
Convert between units, and practise the colour code at your own pace.
Repair dossiers
A dossier for every repair
Keep track of a repair in one place: a dossier per device with the photo of the board, your notes, and every part with its status (measured, faulty or replaced) and the value you measured. The shopping list collects everything marked faulty, from all your dossiers.
- Share a dossier as text, CSV or PDF.
- The parts bin: what you have in stock, and how many.
- Search through all your scans and dossiers.
- Backup as a file, to restore on a new phone.
Price
Free to use, the full version your way
Download Rainbohm for free. Loose parts, resistors, codes and calculators stay free. The full version unlocks chips and transistors, measuring and dossiers, and unlimited circuit-board scans: per month, per year, or with one payment for good. Never ads, no account.
Free
For as long as you like
- Loose parts: what type it is
- Resistors: colour bands, with candidates when unsure
- Markings on SMD resistors and capacitors, electrolytics and fuses
- All codes and calculators
- Three circuit-board scans to try
Full version
€1.99 per month
Or €14.99 per year, or €39.99 once for good. Cancel at any time.
- Circuit board: every part in one photo, without limit
- Chips and transistors: type number, pinout, limits and replacements
- How to measure and what to watch when replacing
- Repair dossiers, the parts bin and export
- Updates included
Google Play shows you the price in your own currency, including VAT, before you buy. A subscription renews automatically until you cancel it; you can cancel at any time in Google Play, under Payments and subscriptions. The full version is linked to your Google account, so it also works on a new phone.
Private
Your photos stay on your phone
Recognition happens entirely on your phone. Rainbohm has no account and no server, and the app does not even have permission to use the internet. More in the privacy policy.
- Only the camera. Used only to recognise parts, on the phone itself.
- No internet access. Android does not let the app go online at all.
- No ads, no tracking. No analytics, no advertising ID.
- No account. No sign-up, no password, no email address.
FAQ
Questions
What can Rainbohm recognise?
A whole circuit board in one photo, with a box around every part it finds. Loose parts, such as capacitors, diodes, transistors, chips, crystals, fuses and relays, with the codes and type numbers printed on them. And resistors by their colour bands, one at a time or a handful in one photo. The database then tells you what a part does, how to measure it and what to watch for when you replace it.
Can it recognise a whole circuit board?
Yes. Take one photo, and every part the app finds gets a frame. Tap a frame to read the marking or the colour bands; only then does the app know what the part is. Read small parts without a marking up close with Part. The free version includes three circuit-board scans, so you can try it; after that it comes with the full version.
Do you need to put the resistor on white paper?
No. Rainbohm reads the bands against any background, in your hand or on the circuit board, and takes the white balance from the body of the resistor itself.
What happens when the app is not sure?
Then you get no single guess, but two to four candidates, each with a drawing, the value and the likelihood. The doubtful band is marked on your own photo. One tap picks the right one, or you choose the colours yourself.
Does Rainbohm need an internet connection?
No. Everything works offline, including the database. The app has no internet permission at all. Only purchases go through the Google Play app on your phone.
Does it tell you how to repair a device?
Rainbohm tells you what a part is, how to measure it and what to watch when you replace it, always with the safety note. It does not give step-by-step repairs of parts that carry mains voltage.
Does it help if colours are hard to tell apart?
Yes. Every colour is also written out by name, in the drawings too, and the app can read the answer aloud.
What does Rainbohm cost?
Downloading is free, and loose parts, resistors, codes and calculators stay free. Chips, measuring and dossiers come with the full version, and unlimited circuit-board scans: €1.99 per month, €14.99 per year, or €39.99 once for good. You can cancel a subscription at any time in Google Play. No ads.
Where can you get Rainbohm?
On Google Play, for Android phones.
Which languages does the app speak?
English, German, Dutch, French, Spanish, Italian, Polish and Portuguese (Brazil).